Description

[{“name”:”Product Name”,”normalizedValue”:”C-1000-M2SC05 Gigabit Ethernet Media Converter Module”,”value”:”C-1000-M2SC05 Gigabit Ethernet Media Converter Module”},{“name”:”Number of SC Ports”,”normalizedValue”:”1″,”value”:”1″},{“name”:”Maximum Distance Supported”,”normalizedValue”:”1,804.46 ft”,”value”:”1804.46 ft”},{“name”:”Total Number of Ports”,”normalizedValue”:”2″,”value”:”2″},{“name”:”Network (RJ-45)”,”normalizedValue”:”Yes”,”value”:”Yes”},{“name”:”Number of Network (RJ-45) Ports”,”normalizedValue”:”1″,”value”:”1″},{“name”:”Environmentally Friendly”,”normalizedValue”:”Yes”,”value”:”Yes”},{“name”:”Network Technology”,”normalizedValue”:”1000Base-SX, 10/100/1000Base-T”,”value”:”1000Base-SX, 10/100/1000Base-T”},{“name”:”Weight (Approximate)”,”normalizedValue”:”5.29 oz”,”value”:”5.29 oz”},{“name”:”Product Type”,”normalizedValue”:”Transceiver/Media Converter”,”value”:”Transceiver/Media Converter”},{“name”:”Compatibility”,”normalizedValue”:”MCR1900 Media Converter Chassis”,”value”:”MCR1900 Media Converter Chassis”},{“name”:”Form Factor”,”normalizedValue”:”Internal”,”value”:”Internal”},{“name”:”1000Base-T”,”normalizedValue”:”Multimode dual SC Media Converters; RJ45 connector, 4 pair CAT 5 UTP cable or cable”,”value”:”Multimode dual SC Media Converters; RJ45 connector, 4 pair CAT 5 UTP cable or cable”},{“name”:”Heat Output ( BTU/HR )”,”normalizedValue”:”10.2″,”value”:”10.2″},{“name”:”Power / TST”,”normalizedValue”:”This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode.”,”value”:”This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode.”},{“name”:”Emissions”,”normalizedValue”:”FCC Part 15 Class A, EN55022 Class A”,”value”:”FCC Part 15 Class A, EN55022 Class A”},{“name”:”Card insertion and removal”,”normalizedValue”:”Captive thumb screws enable fast insertion and removal Can be further tighten with a screwdriver.”,”value”:”Captive thumb screws enable fast insertion and removal. Can be further tighten with a screwdriver.”},{“name”:”Duplex”,”normalizedValue”:”AUTO -The Media converter will advertise Full Duplex Not Capable, Half Duplex Capable., Full – The media converter will advertise Full Duplex Capable, Half Duplex Capable”,”value”:”Full (Default-Up)- The media converter will advertise Full Duplex Capable, Half Duplex Capable; AUTO (Down)-The Media converter will advertise Full Duplex Not Capable, Half Duplex Capable.”},{“name”:”Operating Altitude”,”normalizedValue”:”Up to 3,048 meters (10,000 feet)”,”value”:”Up to 3,048 meters (10,000 feet)”},{“name”:”Immunity”,”normalizedValue”:”EN55024″,”value”:”EN55024″},{“name”:”Fiber link on / Receive activity (LKF)”,”normalizedValue”:”This green LED is operational only when power is applied. The LED is on when the 1000Base-X link is on and flashes with a 50% duty cycle when data is received. The LED will slow blink when the 1000Base-X interface has been taken down as a result of a fault on the 1000Base-T interface.”,”value”:”This green LED is operational only when power is applied. The LED is on when the 1000Base-X link is on and flashes with a 50% duty cycle when data is received. The LED will slow blink when the 1000Base-X interface has been taken down as a result of a fault on the 1000Base-T interface.”},{“name”:”Remote Loopback”,”normalizedValue”:”The media converter can perform a loopback on the 1000Base-X fiber interface; Disabled (Default – Up); Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. The 1000Base-T transmitter is taken off the interface.”,”value”:”The media converter can perform a loopback on the 1000Base-X fiber interface; Disabled (Default – Up); Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. The 1000Base-T transmitter is taken off the interface.”},{“name”:”Copper link on / Receive activity (LKC)”,”normalizedValue”:”This green LED is operational only when power is applied. The LED i on when the 1000Base-T link is on and flashes with a 50% duty cycle when data is received. The LED will slow blink when the 1000Base-T interface has been taken down as a result of a fault on the 1000Base-T interface.”,”value”:”This green LED is operational only when power is applied. The LED i on when the 1000Base-T link is on and flashes with a 50% duty cycle when data is received. The LED will slow blink when the 1000Base-T interface has been taken down as a result of a fault on the 1000Base-T interface.”},{“name”:”Auto-Negotiation”,”normalizedValue”:”Enabled (Default – Up)- In this mode the 1000Base-X and the 1000Base-T will negotiate to the HCD of the two link partners. The 1000Base-X will link up after the negotiation is completed and the 1000Base-T has linked up; Disabled- The 1000Base-X will not use auto negotiation. The 1000Base-T will negotiate to the HCD of the Switch settings and the link partner.”,”value”:”Enabled (Default – Up)- In this mode the 1000Base-X and the 1000Base-T will negotiate to the HCD of the two link partners. The 1000Base-X will link up after the negotiation is completed and the 1000Base-T has linked up; Disabled- The 1000Base-X will not use auto negotiation. The 1000Base-T will negotiate to the HCD of the Switch settings and the link partner.”},{“name”:”Edge Connecter”,”normalizedValue”:”32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for ground and power”,”value”:”32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for ground and power”},{“name”:”Maximum Power Consumption ( Watts )”,”normalizedValue”:”3″,”value”:”3″},{“name”:”Pause”,”normalizedValue”:”When Fiber Auto Negotiation is disabled Pause should only be enabled when all devices connected to the media converter support pause; Enabled(Default)- The Media converter will advertise Pause capable, Asymmetric pause not needed during Auto-Negotiation; Disabled- The Media converter will advertise that it does not have Pause capability during Auto-Negotiation.”,”value”:”When Fiber Auto Negotiation is disabled Pause should only be enabled when all devices connected to the media converter support pause; Enabled(Default)- The Media converter will advertise Pause capable, Asymmetric pause not needed during Auto-Negotiation; Disabled- The Media converter will advertise that it does not have Pause capability during Auto-Negotiation.”},{“name”:”Operating temperature”,”normalizedValue”:”0° C to 50° C (32° F to 122° F)”,”value”:”0° C to 50° C (32° F to 122° F)”},{“name”:”Magnetic Isolation”,”normalizedValue”:”1.5kv”,”value”:”1.5kv”},{“name”:”Fiber Fault Alert”,”normalizedValue”:”The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled; Enabled (Default – Up); When the 1000Base-X receiver is off the 1000Base-X transmitter is turned off. Periodically the 1000Base-X receiver will be turned on for a short period to allow the condition to clear if the 1000Base-X link partner is using a similar feature; Disabled (Down)”,”value”:”The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled; Enabled (Default – Up); When the 1000Base-X receiver is off the 1000Base-X transmitter is turned off. Periodically the 1000Base-X receiver will be turned on for a short period to allow the condition to clear if the 1000Base-X link partner is using a similar feature; Disabled (Down)”},{“name”:”Laser Safety”,”normalizedValue”:”EN 60825-1:2007″,”value”:”EN 60825-1:2007″},{“name”:”Storage temperature”,”normalizedValue”:”minimum range of -25° C to 70° C (-13° F to 158° F)”,”value”:”minimum range of -25° C to 70° C (-13° F to 158° F)”},{“name”:”Operating Humidity”,”normalizedValue”:”5% to 90% non-condensing”,”value”:”5% to 90% non-condensing”},{“name”:”Bit Error Rate (BER)”,”normalizedValue”:”<10-12","value":"<10-12"},{"name":"Storage Humidity","normalizedValue":"5% to 95% non-condensing","value":"5% to 95% non-condensing"},{"name":"Electrical Safety","normalizedValue":"UL 60950-1","value":"UL 60950-1"},{"name":"Country of Origin (subject to change)","normalizedValue":"Canada","value":"Canada"},{"name":"Package Quantity","normalizedValue":"1","value":"1"}]