Description

[{“name”:”Current”,”normalizedValue”:”0.29 amps”,”value”:”0.29 amps”},{“name”:”Fiber Optic Cable”,”normalizedValue”:”Multimode dual SC [ 2 km/1.2 ] to single dual SC fiber connector model; Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron; Single Mode: 9/125 micron (ITu-T 625)”,”value”:”Multimode dual SC [ 2 km/1.2 ] to single dual SC fiber connector model; Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron; Single Mode: 9/125 micron (ITu-T 625)”},{“name”:”Storage temperature”,”normalizedValue”:”minimum range of -25 C to 70 C (-13 F to 158 F)”,”value”:”minimum range of -25 C to 70 C (-13 F to 158 F)”},{“name”:”Heat Output ( BTU/HR )”,”normalizedValue”:”11.9″,”value”:”11.9″},{“name”:”Remote Loopback #2″,”normalizedValue”:”The media converter can perform a loopback on the link #1 fiber interface; Disabled ; Enabled – The 100Base-X receiver is looped to the 100Base-X transmitter. Link #1’s fiber transmitter is taken off the interface.”,”value”:”The media converter can perform a loopback on the link #1 fiber interface; Disabled (Default – Up); Enabled – The 100Base-X receiver is looped to the 100Base-X transmitter. Link #1’s fiber transmitter is taken off the interface.”},{“name”:”Fiber link 1 / Receive activity (LK1)”,”normalizedValue”:”This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.”,”value”:”This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.”},{“name”:”Input Supply Voltage”,”normalizedValue”:”6 – 30 vDC, unregulated ( 12 vDC Nominal )”,”value”:”6 – 30 vDC, unregulated ( 12 vDC Nominal )”},{“name”:”Laser Safety”,”normalizedValue”:”EN 60825-1:2007″,”value”:”EN 60825-1:2007″},{“name”:”Power Consumption”,”normalizedValue”:”3.5 Watts”,”value”:”3.5 watts”},{“name”:”Fiber link 2 on / Receive activity (LK2)”,”normalizedValue”:”This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.”,”value”:”This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.”},{“name”:”Operating temperature”,”normalizedValue”:”0 C to 50 C (32 F to 122 F)”,”value”:”0 C to 50 C (32 F to 122 F)”},{“name”:”Electrical Safety”,”normalizedValue”:”UL 60950-1″,”value”:”UL 60950-1″},{“name”:”Emissions”,”normalizedValue”:”FCC Part 15 Class B*, EN55022 Class B*”,”value”:”FCC Part 15 Class B*, EN55022 Class B*”},{“name”:”Dimensions”,”normalizedValue”:”120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches”,”value”:”120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches”},{“name”:”Power Connector”,”normalizedValue”:”5.5mm x 9.5mm x 2.1mm barrel socket”,”value”:”5.5mm x 9.5mm x 2.1mm barrel socket”},{“name”:”Power / TST”,”normalizedValue”:”This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when in Loopback test mode.”,”value”:”This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when in Loopback test mode.”},{“name”:”Operating Altitude”,”normalizedValue”:”Up to 3,048 meters (10,000 feet)”,”value”:”Up to 3,048 meters (10,000 feet)”},{“name”:”Operating Humidity”,”normalizedValue”:”5% to 90% non-condensing”,”value”:”5% to 90% non-condensing”},{“name”:”Bit Error Rate (BER)”,”normalizedValue”:”\u003c10-12″,”value”:”\u003c10-12″},{“name”:”Storage Humidity”,”normalizedValue”:”5% to 95% non-condensing”,”value”:”5% to 95% non-condensing”},{“name”:”Remote Loopback #1″,”normalizedValue”:”The media converter can perform a loopback on the link #1 fiber interface; Disabled (Default – Up); Enabled- The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface.”,”value”:”The media converter can perform a loopback on the link #1 fiber interface; Disabled (Default – Up); Enabled- The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface.”},{“name”:”Immunity”,”normalizedValue”:”EN55024″,”value”:”EN55024″},{“name”:”Link Pass Through”,”normalizedValue”:”Enabled (Default)- When the state of the receiver is changed on one of the 100Base-X interfaces it is reflected on the other 100Base-X fiber transmitter.If disabled,the 100Base-X fiber interfaces operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the other interface.”,”value”:”Enabled (Default)- When the state of the receiver is changed on one of the 100Base-X interfaces it is reflected on the other 100Base-X fiber transmitter.If disabled,the 100Base-X fiber interfaces operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the other interface.”},{“name”:”Universal AC/DC adapter”,”normalizedValue”:”100-240v AC, regulated DC adapter included”,”value”:”100-240v AC, regulated DC adapter included”},{“name”:”Country of Origin (subject to change)”,”normalizedValue”:”Canada”,”value”:”Canada”},{“name”:”Package Quantity”,”normalizedValue”:”1″,”value”:”1″}]