Description

[{“name”:”Universal AC/DC adapter”,”normalizedValue”:”100-240v AC, regulated DC adapter included”,”value”:”100-240v AC, regulated DC adapter included”},{“name”:”Remote Loopback #2″,”normalizedValue”:”The media converter can perform a loopback on the link #2 fiber interface; Disabled ; Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. Link #1’s fiber transmitter is taken off the interface”,”value”:”The media converter can perform a loopback on the link #2 fiber interface; Disabled (Default – Up); Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. Link #1’s fiber transmitter is taken off the interface”},{“name”:”Power / TST”,”normalizedValue”:”This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when in Loopback test mode.”,”value”:”This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when in Loopback test mode.”},{“name”:”Operating Humidity”,”normalizedValue”:”5% to 90% non-condensing”,”value”:”5% to 90% non-condensing”},{“name”:”1000Base-X”,”normalizedValue”:”Multimode dual SC [ 550 m/1804 ft ] to single mode single SC fiber connector model; Available in SC, ST and LC connector models”,”value”:”Multimode dual SC [ 550 m/1804 ft ] to single mode single SC fiber connector model; Available in SC, ST and LC connector models”},{“name”:”Storage Humidity”,”normalizedValue”:”5% to 95% non-condensing”,”value”:”5% to 95% non-condensing”},{“name”:”Bit Error Rate (BER)”,”normalizedValue”:”<10-12","value":"<10-12"},{"name":"Fiber Fault Alert","normalizedValue":"Enabled - (default up)- If the media converter detects a loss of fiber signal on a fiber receiver, it will immediately disable its fiber transmitter signal. This, in effect, notifies the remote fiber link partner that an error condition exists on the fiber connection. The setting of this switch applies to both fiber ports; Disabled: The media converter will not monitor for fiber fault or generate them.","value":"Enabled - (default up)- If the media converter detects a loss of fiber signal on a fiber receiver, it will immediately disable its fiber transmitter signal. This, in effect, notifies the remote fiber link partner that an error condition exists on the fiber connection. The setting of this switch applies to both fiber ports; Disabled: The media converter will not monitor for fiber fault or generate them."},{"name":"Emissions","normalizedValue":"FCC Part 15 Class A, EN55022 Class A","value":"FCC Part 15 Class A, EN55022 Class A"},{"name":"Power Consumption","normalizedValue":"2.5 watts","value":"2.5 watts"},{"name":"Immunity","normalizedValue":"EN55024","value":"EN55024"},{"name":"Storage temperature","normalizedValue":"minimum range of -25° C to 70° C (-13° F to 158° F)","value":"minimum range of -25° C to 70° C (-13° F to 158° F)"},{"name":"Operating Altitude","normalizedValue":"Up to 3,048 meters (10,000 feet)","value":"Up to 3,048 meters (10,000 feet)"},{"name":"Operating temperature","normalizedValue":"0° C to 50° C (32° F to 122° F)","value":"0° C to 50° C (32° F to 122° F)"},{"name":"Heat Output ( BTU/HR )","normalizedValue":"8.53","value":"8.53"},{"name":"Power Connector","normalizedValue":"5.5mm x 9.5mm x 2.1mm barrel socket","value":"5.5mm x 9.5mm x 2.1mm barrel socket"},{"name":"Input Supply Voltage","normalizedValue":"6 - 30 vDC, unregulated ( 12 vDC Nominal )","value":"6 - 30 vDC, unregulated ( 12 vDC Nominal )"},{"name":"Laser Safety","normalizedValue":"EN 60825-1:2007","value":"EN 60825-1:2007"},{"name":"Dimensions","normalizedValue":"120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches","value":"120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches"},{"name":"Electrical Safety","normalizedValue":"UL 60950-1","value":"UL 60950-1"},{"name":"Current","normalizedValue":"0.21 amps","value":"0.21 amps"},{"name":"Fiber link 1 / Receive activity (LK1)","normalizedValue":"This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.","value":"This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received."},{"name":"Fiber link 2 on / Receive activity (LK2)","normalizedValue":"This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.","value":"This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received."},{"name":"Remote Loopback #1","normalizedValue":"The media converter can perform a loopback on the link #1 fiber interface; Disabled (Default - Up); Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. Link #2's fiber transmitter is taken off the interface","value":"The media converter can perform a loopback on the link #1 fiber interface; Disabled (Default - Up); Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. Link #2's fiber transmitter is taken off the interface"},{"name":"Auto-Negotiation","normalizedValue":"Auto (default up)- Fiber Negotiation is performed for both fiber ports. Full and half duplex will be advertised. Pause will advertise support for Symmetrical and Asymmetrical Pause. Pause frame will not be acted upon or generated but will be passed through; Off- Negotiation on both fiber ports will be disabled. Settings of Link mode and Fiber fault alert will be determined by those switch settings. Pause frames will not be acted upon or generated but will continue to be passed through.","value":"Auto (default up)- Fiber Negotiation is performed for both fiber ports. Full and half duplex will be advertised. Pause will advertise support for Symmetrical and Asymmetrical Pause. Pause frame will not be acted upon or generated but will be passed through; Off- Negotiation on both fiber ports will be disabled. Settings of Link mode and Fiber fault alert will be determined by those switch settings. Pause frames will not be acted upon or generated but will continue to be passed through."},{"name":"Country of Origin (subject to change)","normalizedValue":"Canada","value":"Canada"},{"name":"Package Quantity","normalizedValue":"1","value":"1"}]