Description

[{“name”:”Product Name”,”normalizedValue”:”C-100MM-S2ST80 Media Converter”,”value”:”C-100MM-S2ST80 Media Converter”},{“name”:”Environmentally Friendly”,”normalizedValue”:”Yes”,”value”:”Yes”},{“name”:”Number of ST Ports”,”normalizedValue”:”2″,”value”:”2″},{“name”:”Maximum Distance Supported”,”normalizedValue”:”49.71 mi”,”value”:”49.71 Mile”},{“name”:”Product Type”,”normalizedValue”:”Transceiver/Media Converter”,”value”:”Transceiver/Media Converter”},{“name”:”Weight (Approximate)”,”normalizedValue”:”5.28 oz”,”value”:”5.28 oz”},{“name”:”Form Factor”,”normalizedValue”:”Internal”,”value”:”Internal”},{“name”:”Fiber Optic Cable Standard”,”normalizedValue”:”9/125 µm, 62.5/125 µm, 85/125 µm, 100/140 µm, 50/125 µm”,”value”:”9/125 µm, 62.5/125 µm, 85/125 µm, 100/140 µm, 50/125 µm”},{“name”:”Network Technology”,”normalizedValue”:”100Base-FX, 100Base-ZX”,”value”:”100Base-FX, 100Base-ZX”},{“name”:”ST Port Type”,”normalizedValue”:”Duplex”,”value”:”Duplex”},{“name”:”Total Number of Ports”,”normalizedValue”:”2″,”value”:”2″},{“name”:”Compatibility”,”normalizedValue”:”MCR1900 Media Converter Chassis”,”value”:”MCR1900 Media Converter Chassis”},{“name”:”Fiber link 2 on / Receive activity (LK2)”,”normalizedValue”:”This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.”,”value”:”This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.”},{“name”:”Maximum Power Consumption ( Watts )”,”normalizedValue”:”3.5″,”value”:”3.5″},{“name”:”Fiber Optic Cable”,”normalizedValue”:”Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron; Single Mode: 9/125 micron (ITU-T 625)”,”value”:”Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron; Single Mode: 9/125 micron (ITU-T 625)”},{“name”:”Link Pass Through”,”normalizedValue”:”Enabled (Default)- When the state of the receiver is changed on one of the 100Base-X interfaces it is reflected on the other 100Base-X fiber transmitter; If disabled, the 100Base-X fiber interfaces operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the other interface.”,”value”:”Enabled (Default)- When the state of the receiver is changed on one of the 100Base-X interfaces it is reflected on the other 100Base-X fiber transmitter; If disabled, the 100Base-X fiber interfaces operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the other interface.”},{“name”:”Heat Output ( BTU/HR )”,”normalizedValue”:”11.9″,”value”:”11.9″},{“name”:”Bit Error Rate (BER)”,”normalizedValue”:”\u003c10-12″,”value”:”\u003c10-12″},{“name”:”Fiber link 1 / Receive activity (LK1)”,”normalizedValue”:”This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.”,”value”:”This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.”},{“name”:”Remote Loopback #2″,”normalizedValue”:”The media converter can perform a loopback on the link #2 fiber interface; Disabled ; Enabled- The 100Base-X receiver is looped to the 100Base-X transmitter. Link #1’s fiber transmitter is taken off the interface.”,”value”:”The media converter can perform a loopback on the link #2 fiber interface; Disabled (Default – Up); Enabled- The 100Base-X receiver is looped to the 100Base-X transmitter. Link #1’s fiber transmitter is taken off the interface.”},{“name”:”Electrical Safety”,”normalizedValue”:”UL 60950-1″,”value”:”UL 60950-1″},{“name”:”Operating Altitude”,”normalizedValue”:”Up to 3,048 meters (10,000 feet)”,”value”:”Up to 3,048 meters (10,000 feet)”},{“name”:”Operating Humidity”,”normalizedValue”:”5% to 90% non-condensing”,”value”:”5% to 90% non-condensing”},{“name”:”Edge Connecter”,”normalizedValue”:”32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for ground and power”,”value”:”32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for ground and power”},{“name”:”Storage Humidity”,”normalizedValue”:”5% to 95% non-condensing”,”value”:”5% to 95% non-condensing”},{“name”:”Immunity”,”normalizedValue”:”EN55024″,”value”:”EN55024″},{“name”:”Card insertion and removal”,”normalizedValue”:”Captive thumb screws enable fast insertion and removal Can be further tighten with a screwdriver.”,”value”:”Captive thumb screws enable fast insertion and removal. Can be further tighten with a screwdriver.”},{“name”:”Operating temperature”,”normalizedValue”:”0 C to 50 C (32 F to 122 F)”,”value”:”0 C to 50 C (32 F to 122 F)”},{“name”:”Emissions”,”normalizedValue”:”FCC Part 15 Class A, EN55022 Class A”,”value”:”FCC Part 15 Class A, EN55022 Class A”},{“name”:”Storage temperature”,”normalizedValue”:”minimum range of -25 C to 70 C (-13 F to 158 F)”,”value”:”minimum range of -25 C to 70 C (-13 F to 158 F)”},{“name”:”Laser Safety”,”normalizedValue”:”EN 60825-1:2007″,”value”:”EN 60825-1:2007″},{“name”:”Power / TST”,”normalizedValue”:”This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when in Loopback test mode.”,”value”:”This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when in Loopback test mode.”},{“name”:”Remote Loopback #1″,”normalizedValue”:”The media converter can perform a loopback on the link #1 fiber interface; Disabled (Default – Up); Enabled- The 100Base-X receiver is looped to the 100Base-X transmitter. Link #2’s fiber transmitter is taken off the interface”,”value”:”The media converter can perform a loopback on the link #1 fiber interface; Disabled (Default – Up); Enabled- The 100Base-X receiver is looped to the 100Base-X transmitter. Link #2’s fiber transmitter is taken off the interface”},{“name”:”Country of Origin (subject to change)”,”normalizedValue”:”Canada”,”value”:”Canada”},{“name”:”Package Quantity”,”normalizedValue”:”1″,”value”:”1″}]