Description

[{“name”:”Card insertion and removal”,”normalizedValue”:”Captive thumb screws enable fast insertion and removal Can be further tighten with a screwdriver.”,”value”:”Captive thumb screws enable fast insertion and removal. Can be further tighten with a screwdriver.”},{“name”:”Edge Connecter”,”normalizedValue”:”32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for ground and power”,”value”:”32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for ground and power”},{“name”:”Auto-Negotiation”,”normalizedValue”:”Auto (default up)- Fiber Negotiation is performed for both fiber ports. Full and half duplex will be advertised. Pause will advertise support for Symmetrical and Asymmetrical Pause. Pause frame will not be acted upon or generated but will be passed through; Off- Negotiation on both fiber ports will be disabled. Settings of Link mode and Fiber fault alert will be determined by those switch settings. Pause frames will not be acted upon or generated but will continue to be passed through.”,”value”:”Auto (default up)- Fiber Negotiation is performed for both fiber ports. Full and half duplex will be advertised. Pause will advertise support for Symmetrical and Asymmetrical Pause. Pause frame will not be acted upon or generated but will be passed through; Off- Negotiation on both fiber ports will be disabled. Settings of Link mode and Fiber fault alert will be determined by those switch settings. Pause frames will not be acted upon or generated but will continue to be passed through.”},{“name”:”Storage Humidity”,”normalizedValue”:”5% to 95% non-condensing”,”value”:”5% to 95% non-condensing”},{“name”:”Operating Humidity”,”normalizedValue”:”5% to 90% non-condensing”,”value”:”5% to 90% non-condensing”},{“name”:”Electrical Safety”,”normalizedValue”:”UL 60950-1″,”value”:”UL 60950-1″},{“name”:”Emissions”,”normalizedValue”:”FCC Part 15 Class A, EN55022 Class A”,”value”:”FCC Part 15 Class A, EN55022 Class A”},{“name”:”Operating temperature”,”normalizedValue”:”0° C to 50° C (32° F to 122° F)”,”value”:”0° C to 50° C (32° F to 122° F)”},{“name”:”Fiber link 2 on / Receive activity (LK2)”,”normalizedValue”:”This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.”,”value”:”This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.”},{“name”:”Storage temperature”,”normalizedValue”:”minimum range of -25° C to 70° C (-13° F to 158° F)”,”value”:”minimum range of -25° C to 70° C (-13° F to 158° F)”},{“name”:”Bit Error Rate (BER)”,”normalizedValue”:”\u003c10-12″,”value”:”\u003c10-12″},{“name”:”Operating Altitude”,”normalizedValue”:”Up to 3,048 meters (10,000 feet)”,”value”:”Up to 3,048 meters (10,000 feet)”},{“name”:”Laser Safety”,”normalizedValue”:”EN 60825-1:2007″,”value”:”EN 60825-1:2007″},{“name”:”Fiber link 1 / Receive activity (LK1)”,”normalizedValue”:”This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.”,”value”:”This green LED is operational only when power is applied. The LED is on when the 100Base-X link is on and flashes with a 50% duty cycle when data is received.”},{“name”:”Power / TST”,”normalizedValue”:”This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when in Loopback test mode.”,”value”:”This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when in Loopback test mode.”},{“name”:”1000Base-X”,”normalizedValue”:”Multimode dual SC to single mode single SC fiber connector model; Available in SC, ST and LC connector models”,”value”:”Multimode dual SC to single mode single SC fiber connector model; Available in SC, ST and LC connector models”},{“name”:”Maximum Power Consumption ( Watts )”,”normalizedValue”:”2.5″,”value”:”2.5″},{“name”:”Immunity”,”normalizedValue”:”EN55024″,”value”:”EN55024″},{“name”:”Remote Loopback #2″,”normalizedValue”:”The media converter can perform a loopback on the link #2 fiber interface; Disabled ; Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. Link #1’s fiber transmitter is taken off the interface”,”value”:”The media converter can perform a loopback on the link #2 fiber interface; Disabled (Default – Up); Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. Link #1’s fiber transmitter is taken off the interface”},{“name”:”Fiber Fault Alert”,”normalizedValue”:”Enabled – (default up)- If the media converter detects a loss of fiber signal on a fiber receiver, it will immediately disable its fiber transmitter signal. This, in effect, notifies the remote fiber link partner that an error condition exists on the fiber connection. The setting of this switch applies to both fiber ports; Disabled: The media converter will not monitor for fiber fault or generate them.”,”value”:”Enabled – (default up)- If the media converter detects a loss of fiber signal on a fiber receiver, it will immediately disable its fiber transmitter signal. This, in effect, notifies the remote fiber link partner that an error condition exists on the fiber connection. The setting of this switch applies to both fiber ports; Disabled: The media converter will not monitor for fiber fault or generate them.”},{“name”:”Remote Loopback #1″,”normalizedValue”:”The media converter can perform a loopback on the link #1 fiber interface; Disabled (Default – Up); Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. Link #2’s fiber transmitter is taken off the interface”,”value”:”The media converter can perform a loopback on the link #1 fiber interface; Disabled (Default – Up); Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. Link #2’s fiber transmitter is taken off the interface”},{“name”:”Heat Output ( BTU/HR )”,”normalizedValue”:”8.53″,”value”:”8.53″},{“name”:”Country of Origin (subject to change)”,”normalizedValue”:”Canada”,”value”:”Canada”},{“name”:”Package Quantity”,”normalizedValue”:”1″,”value”:”1″}]